基于同轴图像传感的激光焊接过程质量监测技术

针对激光焊接过程中由于参数不匹配、装配误差等原因造成的焊接过程不稳定等焊接缺陷，基于同轴图像传感技术，建立起一套激光焊接过程中的质量在线监测系统，对焊接过程中的熔池图像进行了采集分析及其熔池特征信息的提取. 结果表明，在激光功率为1 500 W的不等厚不锈钢薄板激光焊接试验条件下，焊接过程中的不稳定、下塌缺陷以及焊偏现象与熔池形状各特征信息变化具有一定的相关性. 结合BP神经网络算法对所提特征信息进行分类、识别，基于LabVIEW软件平台，可实现相应缺陷的自动化识别及报警功能.     

0CrMnTiH齿轮钢的淬透性计算及窄淬透性带控制

采用非线性方程计算法计算20CrMnTiH钢末端淬透性,只需利用生产实际数据加以修正,就能进行精确的淬透性计算和预报,与实测值偏差不超过2HRC。采用化学成分设计和控制,保证20CrMnTiH钢△[C]不超过0.007%,△[Si]波动不超过0.04%,△[Mn]、△[Cr]不超过0.02%,△[Ti]不超过0.01%,△[Alt]不超过0.010%,[Ni]、[Cu]不超过0.05%,[Mo]、[W]、[V]不超过0.03%,[P]、[S]不超过0.020%,[N]和[B]分别不超过0.006 0%和0.0005%,并控制碳偏析指数不超过1.035%,可实现国际先进水平的末端淬透性HRC4带宽控制。     

Neutron Diffraction and Neutron Radiography Investigation into Powder Sintering of Ti/Al and TiH2/Al Compacts

Metallurgical and Materials Transactions B - Sintering behaviors of two types of powder compact, i.e., Ti/Al and TiH2/Al, under vacuum were studied using in situ neutron diffraction, in situ...     

Controlled Secure Direct Communication Protocol via the Three-Qubit Partially Entangled Set of States

In this paper, we first re-examine the previous protocol of controlled quantum secure direct communication of Zhang et al.’s scheme, which was found insecure under two kinds of attacks, fake entangled particles attack and disentanglement attack. Then, by changing the party of the preparation of cluster states and using unitary operations, we present an improved protocol which can avoid these two kinds of attacks. Moreover, the protocol is proposed using the three-qubit partially entangled set of states. It is more efficient by only using three particles rather than four or even more to transmit one bit secret information. Given our using state is much easier to prepare for multiqubit states and our protocol needs less measurement resource, it makes this protocol more convenient from an applied point of view.     

Introduction

正At the instigation of some of Emeritus Professor Edwin Thomas(Ted) Brown’s PhD students, a Colloquium in his honour to celebrate his retirement and a long and distinguished career in rock mechanics was held in Brisbane, Australia on the 4th December2018, Ted’s 80th birthday.Ted was born in Castlemaine, Victoria, Australia, on 4 December     

Influence of lanthanum on enhancement of mechanical and electrical properties of Cu-Al_2O_3 composites

Two kinds of Cu-Al_2O_3 composites(with and without La) were prepared via mechanical alloying-spark plasma sintering(MA-SPS) method. Microstructure, mechanical properties and electrical resistivity were investigated systematically using metallography, scanning electron microscopy, transmission electron microscopy, mechanical and electrical properties testing. The results indicate that an appropriate amount of La can homogenize the distribution of Al_2O_3. As such, yield strength, ultimate tensile strength and elongation of Cu-Al_2O_3-La are greatly increased. Some semi-coherent interface between Cu and Al_2O_3 is found, which means a low interface energy. The grain shape of Cu changes to irregular band with the addition of La. This change results in a density decrease of grain boundary and reduces electrical resistance. Lanthanum may exist in the form of La_2O_3.     

一种抗运动干扰的实时心率提取方法

针对基于容积脉搏波（PPG）提取运动心率时，传统心率提取算法由于运动噪声干扰使测量结果误差大、实时性不好的问题，提出一种抗运动干扰的实时心率提取方法。该方法通过实时小波去噪，同时结合三轴加速度信号（ACC）对运动进行分类训练，计算各运动状态心率增益，对实时心率值进行补偿。实验结果表明，通过与同时采集的ECG信号计算出的实时心率进行对比，绝对误差率仅为1.2%左右。相比传统心率提取算法，该算法具有抗干扰性强，实时准确的特点。     

超高强7055铝合金铸锭均匀化工艺优化

采用光学显微镜、扫描电镜、差热分析及透射电镜等手段,对一种航空用超高强7055铝合金大尺寸铸锭的均匀化工艺进行分析与优化。提出分级提高均匀化温度的方法,在确保不发生过烧的情况下,最大限度改善铸锭质量。结果显示:低温预均匀化时,铸锭中析出大量的Al₃Zr相,能够大幅度降低对后续挤压变形的再结晶比例;对铸锭采用400 ℃×4 h+465 ℃×16 h+474 ℃×8 h的分级均匀化处理工艺,能够显著消除铸锭中低熔点相的含量,提高铸锭质量,同时相比于原工艺节省约13 h。新的均匀化处理工艺,不仅提高了生产效率,还能够为后续工艺提供良好的铸锭。     

提高新疆准东露天煤成浆性的实验研究

为提高准东露天煤的成浆性能,利用宽沟煤、乌东煤、北山煤、黑山煤、红沙泉煤5种煤与准东露天煤进行了混合制浆实验,考察了各单种煤的成浆性能以及单种煤最高成浆浓度条件下混合制浆的煤浆性能。单一准东露天煤浆的成浆性研究表明:准东露天煤单独制浆时,在添加剂添加率3‰下,煤浆最高质量分数为47%,黏度650 mPa·s,但煤浆流动性和稳定性一般。与不同种煤混合制浆研究表明:准东露天煤与宽沟煤、黑山煤容易混合成浆,煤浆的浓度、流动性、稳定性均有明显提高;在准东露天煤与宽沟煤、黑山煤质量比5∶5时,煤浆质量分数可达57%,可满足水煤浆气化炉生产对煤浆的要求。